DIY: Mock Pallet End Table Top

I have a slight obsession with pallets that are turned into coffee tables. I think it's amazingly resourceful and looks wonderful, if you have the right pallet. We are planning on attempting a pallet coffee table for the new house but we have never been big into coffee tables, mostly because the dogs like to run around. What I really wanted to do was create end tables out of pallets but something that size is really hard to come by. So a few weeks back I had an idea to create an end table that looks like a pallet out of furring strips and some 2x4 studs. It was a super simple project and I'm excited to share it with you.

For this project we bought:

• 2- 2x4x8
• 3- Furring Strips 1x3x8
• Plus wood for legs (will get to that later)

Cut List

• 2  - 2x4 @ 24" (for table top support)
• 3 - 2x4 @ 21" (again for table top support)
• 9 - 1x3 @ 24" (for table top)

Tools we needed

• Miter Saw
• Drill
• Counter sink bit
• Phillips head bit
• 7/64" drill bit*
• Measuring tape
• Pencil
• Hammer
• 12- 2" wood screws
• 27- 1 1/4" finishing nails

* Just needs to be a little bit smaller than the screw

First Andy and I measured and cut all the wood, (yes I used the saw and I was proud). 

Then we arranged the 24" 2x4's and the 21" 2x4's like so: 

Basically, we created a box out of the 4 pieces and then added a brace in between to stabilize the table top.
Andy then used the drill bit to drill a guide hole for the screw, used the counter sink so the screw head would sit flush with the table, then actually screwed it in. He repeated this process two times at each of the four corners and also two times on each side of the brace beam.

You can see the counter sink next to where he is drilling. 

Actually screwing the pieces together.

Once that was completed we had to nail the table top on. With this portion we just laid out the nine 24" 1x3's across the table and arranged them so that the spaces were even. This was, for us, just a trial and error process. We could have used less 1x3's and had bigger spaces in the table top or we could have used more and had zero spaces in the table top. It's really whatever you prefer. We preferred something like this:

Once we figured out how we wanted the spaces we made a little mark on each side of the base where we wanted each piece of wood, this made it easier when we started nailing them all. We just nailed each piece three times. Once on either side and one in the middle where the support beam is. We used finishing nails because it gave it a cleaner look but you could also use standard nails to make it more pallet like.

Voila we had a table top. Which is where this project stops. See, we want these to be our end tables but we don't have a couch for our great room yet, so we really want them to sit flush (or at least) close to our couch so we are waiting on the leg portion of this project until we figure out what size our couch is going to be. I promise to post a link to the leg portion of this project when we get to it.

DIY: Book Mobile Part 1

Remember this project:

Well I did it! I found my cable spool! I just have to say Home Depot rocks! We were wandering through the store the other day and I saw a cable spool that looked to be a good size for a coffee table. So I asked an associate if I could have one and after some chit chat we got to take it home for free! Woot! While we were there we picked up the rest of the supplies for the project, 4 dowel rods 3/4", 3 casters, and some paint.

Beautiful isn't it!

It's even better than I could have hoped for, I mean it's in great shape. So this weekend Andy and I decided to work on turning it to a table for the new house. First thing we had to do was try to pound  down the nails to make the top surface even. 

We tried a chisel and hammer but the wood was way tougher than we expected, so we ended up just using the hammer. After about fifty billion strikes we used some wood putty over the nails and over the jagged bits to give the surface a smoother texture. 

Before putty...

After putty!

Once the surface was looking like it wouldn't cut somebody it was time for measurements to figure out where to put the spokes. 

Andy is much better with measurements so he took over at this point (and yes that is my cup of coffee sitting on the spool, I was testing it out)

Andy thought that a clock pattern would be best for the placement of the dowel rods. He measured across the spool and marked about and inch in on either size at 12 and 6 then again at 9 and 3. Then he went around between 12-3, 3-6, 6-9, 9-12 and put two more marks in between each set roughly equal distance apart (I say roughly because there were a lot of nails and he was trying hard not to hit any of them when it came time to drill). 

Next Andy and I took the spool outside and used a 3/4" spade bit to drill the holes at the marks. There were some complications during this project as Andy hit nails in three different spots. To remedy this he simply used a chisel and hammer to hit the nails back and finished drilling. Once all the holes were complete we had to measure the dowel rods for sawing. 

Andy simply placed one into the hole and made a pen mark at the point where the dowel hit the table top. During the saw process he simply went a little under the mark so that the dowel wouldn't stick up out of the hole on the table. After sawing all the dowels we forced them through the holes on the spool and it's really starting to look like a book shelf table!

(Pardon the wonky dowel rod, it is a work in progress)

Stay tuned as tomorrow will unveil part two of this project!

New Obsession

Ever since the wedding I have had this hole, I mean for the year or so before the wedding I spent my time looking up ideas, trying to find things that I could make myself to make the wedding unique and pretty. When there was no more wedding I had a hard time with all the free time I had and crafting had turned into a drug for me. See I have a lot of nervous energy and I get anxious at times, crafting really helped me to calm those feelings and  let me feel useful. Now that I'm working I feel useful but a lot of the time I still have no projects (other than cleaning) to put that anxious/nervous energy in to. That is until I found http://ana-white.com/ and fell in love. This was the answer to my crafting withdraw. I obviously need furniture for our house and what better way to save money than to make it. So this past weekend, Andy and I set out for Home Depot and bought wood and supplies for this project and this project. The first project (the crate shelf) was my own undertaking, and in my humble opinion the result turned out pretty good:

As for the chair, I'll admit that was a bit too much for me by myself so I more or less just assisted Andy but it is looking like it will turn out pretty well. It is by no means done yet, there was a problem with the leg and I want to paint it too but I think it will be fantastic once it is completed. Here's some pictures from the work site and the nearly completed chair:

There were a few shots of him bending over but I thought he might not appreciate it (trust me though, he looks hot, well, to me). Isn't my husband truly awesome? I think that we might make a habit of this woodworking together thing. It's a great way for us to bond and we have something really great as an end product. Though I think if it becomes habit I'm going to have to learn how to not be afraid of the saw. And just for fun, some future plans I think we might be working on: a headboard (as we currently have none) and a bench/storage (our hall is looking a little drab), plus another chair or two for the deck plus a little coffee table. Love it.

What projects do you and your significant other do together?